Magnet
Magnet
 |
 2007 TEREX PEGSON 1412 TRACKPACTOR IMPACT CRUSHER 550 TPH MAGNET CONVEYOR  US $485,000.00
|
 Stearns 96 10KW sweeper magnet New rewind US $18,750.00
|
 RC2S200TPI 120V ADVANCE MAGNETIC BALLAST 1 2Lamp QTY100 US $18,400.00 |
 NEW ELECTRO SUSPENSION STATIONARY MAGNET WITH RECTIFIER 36 42 BELT US $13,000.00
|
 Stearns 30 X 120 Magnetic Separators US $12,500.00
|
 Fein 3 1 8 Auto Magnetic Core Drill Press KBM80AUTO US $4,983.00
|
 Fein 3 1 8 Magnetic Core Drill Press KBM80U US $4,151.00
|
 MCR3 Machine Control Laser Receiver w Magnetic MT US $2,499.00
|
 Fein 2 1 16 Reversible Magnetic Core Drill KBM 52U NEW US $1,928.00
|
 Fein KBM 50 QX 2 Speed 2 1 16 inch Magnetic Core Drill US $1,714.00
|
 Fein 2 1 16 Magnetic Core Drill Press KBM 50 QX NEW US $1,704.00
|
 Fein KBM 32Q 1 1 4 Inch Capacity Magnetic Core Drill US $1,329.00
|
 Fein 1 1 4 440rpm Magnetic Core Drill Press KBM32Q NEW US $1,319.00
|
 Lot of 50 MAGNETEK 827 SLH TC P MAGNETIC FLUORESCENT BALLAST 2x F96 84 72T12 6 US $999.00
|
 DETEX Exit Device V40 Value Series Rim Exit Device Delayed Egress Magnetic US $998.95
|
 MILWAUKEE MAGNETIC DRILL PRESS MODEL 4203 US $989.00
|
 Milwaukee Magnetic Drill Press Base 4203 NEW US $926.98
|
 DeWalt DW159 Heavy Duty Magnetic Drill Press US $900.00
|
 JANCY SLUGGER MAX 2X2 MAGNETIC DRILL MODEL MT2 WITH CASE US $889.00
|
 CST Magna Trak 102 Magnetic Locator w Hard Case US $875.00
|
 CST Magna Trak 202 Magnetic Locator w Hard Case US $875.00
|
 CST Magna Trak 102 Magnetic Locator w Soft Case US $850.00
|
 CST Magna Trak 202 Magnetic Locator w Soft Case US $850.00
|
 JANCY SLUGGER USA5 USA 5 MAGNETIC DRILL PRESS US $850.00 |
 Hougen Magnetic Drill Press HMD115 Low Profile BRAND NEW US $915.00
|
 RS2S200FOI 120V ADVANCE MAGNETIC WP BALLAST 2Lamp 2 Pk US $828.32 |
What is the Best Way to Cut a Small magnet in Half?
I need a tiny magnet. I have a Round One (a fridge magnet) that is nice and small, and it would be nice to have it in Two halves, but I am worried that the process of Cutting it might mess up its magnetism.
You Can indeed produce two separate permanent magnets by cutting it in half. A few things you Must be concerned about though.
1) Do Not mechanically Hit the magnet too Hard.
2) Do not Heat it up too much (Blow Torch cutting Out of the question, haha).
3) Do not induce a reverse Magnetic flux (unlikely you will do this either, haha).
These Three things can impart enough energy to the magnet that its "magnetic domains" will randomize (as opposed to the aligned nature of the domains in a permanent magnet). So, just Clamp the magnet in place and Use a Fine Cutting Tool of Your choice. If you have one of those Dremel Tools it might have a fine cutting Attachment.
Then again, magnets are Cheap. Why not just buy a Bag of new ones the size you want?
